Regał do przechowywania kasetek z przegródkami
kształt wczepów
odstęp na początku i końcu krawędzi (wielokrotność zwykłego odstępu)
wysokość wystających występów dolnych (wielokrotność grubości), tylko krawędź z otworami
margines pod otworami na wczepy (wielokrotność grubości)
naddatek materiału do zeszlifowania przypaleń (wielokrotność grubości)
szerokość wczepów (wielokrotność grubości)
luz na wczepach, żeby łatwo wchodziły (wielokrotność grubości)
odstęp między wczepami (wielokrotność grubości)
szerokość otworów na wczepy (wielokrotność grubości)
inside angle of the feet
height of strips to be glued to the inside of bottom edges (multiples of thickness)
height of the feet (multiples of thickness)
distance from finger holes to bottom edge (multiples of thickness)
width of the feet (multiples of thickness)
have lid overlap at the sides (similar to OutSetEdge)
set to lower value to get disks surrounding the pins
diameter of the pin hole (multiples of thickness)
fixed length of the grips on he lids (multiples of thickness)
thickness of the arc holding the pin in place (multiples of thickness)
diameter of the pin hole in mm
pieces per hinge
number of hinges per edge
style of hinge used
radius of the eye (multiples of thickness)
space between eyes (multiples of thickness)
minimum space around the hinge (multiples of thickness)
width of the "finger hole" in mm
additional pin for better positioning
position(s) of the extra locking springs in the lid
angle of the hooks bending outward
radius at the bottom (multiples of thickness)
length of the hooks (multiples of thickness)
height above the wall
radius of hole
radius of top corner
extend the triangle along the length of the edge (multiples of thickness)
head diameter of mounting screw (in mm)
shaft diameter of mounting screw (in mm)
minimum space left and right without holes (fraction of the edge length)
number of mounting holes (integer)
side of box (not all valid configurations make sense...)
edge style
height above the wall in mm
height of hole(s) in percentage of maximum hole height (handle height - 2 * material thickness)
width of hole(s) in percentage of maximum hole width (width of edge - (n+1) * material thickness)
added to side panels if checked, to front and back otherwise (only used with top_edge parameter)
radius of corners in mm
extend the handle along the length of the edge (multiples of thickness)
szerokość wewnętrzna w mm (zewnętrzna, gdy zaznaczono „wymiary zewnętrzne”)
głębokości przegródek od tyłu do przodu w mm, np. 50*2 = dwie po 50 mm 🛈
wysokości przegródek od dołu do góry w mm 🛈
wpisane wymiary są zewnętrzne (z grubością ścianek); bez zaznaczenia są wewnętrzne 🛈
rodzaj krawędzi dolnej
rodzaj krawędzi górnej (np. bez wieka, z wiekiem)
height of retaining wall at the front edges
use finger hole edge for retainer walls
grubość materiału w mm; od niej zależy głębokość wczepów 🛈
korekta szczeliny w mm = POŁOWA szerokości cięcia lasera (kontur przesuwa się o tę wartość w każdą stronę). Uwaga: w edytorze pudełek wpisuje się PEŁNĄ szerokość cięcia, tu połowę. Większa wartość = ciaśniejsze spasowanie. Wartość dobierzesz wzorcem do kalibracji szczeliny. 🛈
format pobieranego pliku 🛈
podpisz części (gdzie to możliwe)
dodaj prostokąt kontrolny o podanej długości w mm (zero = bez prostokąta) 🛈
szerokość mostków trzymających części w arkuszu, w mm (nie we wszystkich wzorach) 🛈
dodaj do pliku kod QR z linkiem do tych ustawień
kształt narożników wewnętrznych 🛈
odstęp wokół części (wielokrotność grubości [: dodatkowe mm]) 🛈
rysuj obrysy pomocnicze niektórych elementów 🛈
Generuj Pobierz Zapisz w adresie Kod QR
This is a simple shelf box.